Do You Wanna Build a Snowman?

515b4075-1dda-4e54-8462-e2b16a368acd

Confession: I have never seen Frozen. Gasp. My kids have, and they, unlike everyoneelseintheworld, were not impressed. Thus, no exposure for mommy. I do sing “Let it Go” whenever they bicker with each other, which is mommygenius because it forces them to instantly team up in an all-out mutual effort to silence me. Heh. Heh. Heh.

But that is beside the point. Despite the fact that I’ve seriously neglected this blog all year long, I’m gonna post a fun DIY to keep on file for next year’s Christmas shenanigans. Ready?

Felt. Snowman. Wall.
Easy as 1-2-3, and makes for hours of creative, mess-free, wintry FUN. Did I mention the no mess part? No paint, glitter, sprinkles or cookie crumbs to sweep/wipe/scrub off the floor. Those activities are glorious, of course. But THIS project is one where you can send your precious little mess-makers whilst you detox the house from the aforementioned explosively-festive crafts.

First: buy some felt. It’s cheap, folks. Buy a couple yards of your background material – I chose red – don’t use white! You could use black, grey, brown, blue…whatever floats your boat, but not a color you plan to use a lot in the foreground. Because a snowman in a blizzard just doesn’t have the same appeal. Buy several other colors as well – white, green, yellow, brown, orange, black, red, etc. You can get half-yards at the cutting counter or those little sheets of felt they sell in crafting supplies.

Pop in It’s a Wonderful Life or While You Were Sleeping, and start snipping: cut out your building pieces. Fabric scissors are best here. Cut big white blobs (snowman body parts), stick pieces (arms), little black blobs (coal), – or multicolored buttons if you’re really up for a challenge! – orange triangles, mittens, boots, hats, scarves, etc. You can cut out big green trees and geometric shapes for presents, or brown geometric pieces to build gingerbread houses…the possibilities are endless! I added lots of white strips and geometric shapes to build giant snowflakes. My kids requested a felt nativity set to put on their wall, but by then Mama’s hands were stiff from all the cutting. Next year, kiddos.

Adhere your backing piece to the wall. We have a big blank wall in my kids’ room that worked perfectly. It ended up being about 5 feet high, 6 feet wide. Next year I hope that wall will be filled with shelves, frames, etc. so we will have to find a new spot. If you have to go over any outlets or switches, measure where they are and cut them out from the backing piece, so they aren’t covered up all season long.

You can stick the felt backing on with painter’s tape (I used green! So festive!), but the bigger it is, the more reinforcement it will need. I busted out the stapler and punched a few staples in where my wall was saggy. If you can’t do that, you could always make tape loops and put them all over your wall prior to sticking/smoothing the felt.

Find a basket or bin to store the building pieces, and let the kids go to town. My kids played with it day after day for hours! Since we used a whole wall, they could both build simultaneously without disturbing each other’s creations. It makes for a fun room decoration when it’s all up, too! Next year, besides cutting a Nativity, I might cut out pieces for them to play felt tic tac toe or other games on their wall.

What would you make for your kids to build? I’d love more ideas!

In His joy,
Monique

 

 

Advertisements

DIY custom closet doors with bookcase

That’s quite a mouthful, and I suppose it ought to be, as my most complex DIY project to date.  Remember when I hinted at more projects in the boys’ room?  Well, this is it!

My kids’ new shared bedroom has an enormous closet.  The opening is 72″ across.  YAY for storage!  But BOO on bi-fold closet doors.  When open, the doors extend way out into the room, cutting into usable space.  The only place for our cozy rocking chair happens to be in a corner by the closet, so with it there, the right hand door wouldn’t open more than a few inches.  Scoot chair–open door–retrieve item–close door–scoot chair.  A workout, maybe?  Functional…Not so much.  I’ve been wanting to replace those doors with sliding bypass doors, but I didn’t want to spend a fortune on a new set.

unnamed (10)
Big fat closet (minus the old doors) – out with the old and on with the new!

That’s when my dear handyman (affectionately referred to as “Mister Joe”) tipped me off to a diamond in the rough – the Habitat for Humanity ReStore.  It’s like everything you ever wanted in a thrift shop…but all for the home!  We’re talking furniture, appliances, hardware, you name it.  They had stacks and stacks of used doors.  Thankfully I thought to bring a tape measure along, so finding just the right pair was a snap.  It cost a whopping $10.  Then, I happened to spot a good ol’ fashioned, working overhead projector (dating myself here –  we used these way back when I was in high school.  Yes.  I’m thirty now.  Be nice.)…SCORE!  I ended up spending just $30 for the perfect set of doors, the projector, and a few assorted picture frames.  I also made friends with a retired trucker, who saw me struggling to tie down the doors on top of my Explorer.  He spent about 15 minutes professionally strapping those babies down so they wouldn’t fly off on the freeway.  Just out of the pure goodness of his heart.  He thought I was hysterical when I asked if he had been a Boy Scout.  🙂

So, thanks to my trucker friend, the doors made it home in one…er…two pieces.  My vision was to build/embellish the fronts, which is another reason why I liked the old flat-faced doors at the ReStore instead of new paneled ones you can get at Home Depot.  The right-hand door, the one by our rocking chair, would transform into a sliding, forward-facing bookshelf.  The left-hand door, which would slide behind the right, would receive some custom paint in the form of a scripture verse.  Doing this would boost the functionality of the room, while bringing in our two favorite funky colors.  When you have  a closet taking up a quarter of the wall space, might as well put it to good decorative use!

Now, construction time.  First step was to sand down the doors and prime them (these were a medium-stain oak, and I wanted white to match our trim).  Then, because the bookcase on the right-hand door would cover the pull-cup handle, I filled that hole using a piece of scrap wood, cut with a 2 1/8″ drill bit.  A little all-purpose spackling putty smoothed it off.  unnamed (14)
Doors all primed and ready to paint.  Note my high tech system for keeping them off the floor to paint the edges.  Paint cans.  Keepin’ it real folks!
unnamed (1)
Filled and putty-ed (puttied?  whatever!) hole

Next, paint.  I painted all sides of the doors except the front-right, which was about to receive the bookcase treatment. 

unnamed
Verse door base is painted; bookcase door is awaiting shelves

Now, carpentry!  I purchased 1×5″ poplar boards from Home Depot and had them all cut to my specifications – five 30″ wide shelves, two 72″ high sides, and ten 30″ dowels to hold the books up.  I measured and fastened the side boards first, using a counter-sink drill bit and screws (so they wouldn’t stick out and scrape anything).  Then I measured and attached the five shelves – further apart on the bottom for taller books, and closer together on top for shorter books.  I used a bead of wood glue as well as counter-sink screws for these.  After the glue dried, I caulked all the seams.  This whole part was new territory for me.  I prayed a lot that I wouldn’t completely destroy it.  Definitely could have used Jesus’ hands-on carpentry expertise here.  🙂
unnamed (3) unnamed (4)
Counter-sink drilled holes (left) and screws in place (right)
unnamed (2) unnamed (6)
Shelves all built (left) and caulked (right)

After construction, I painted the entire front of the bookshelf door.  I didn’t bother to prime the shelves, since I wasn’t concerned about paint sticking to bare wood.  After a couple coats, I fastened on the previously painted dowels (counter-sink again).  I did these one side at a time, which helped get all of them evenly tight on both sides.  One or two dowels were cut just a smidge too short, so I filled the slight gap on one side with a bit of putty.  Gave the whole thing a 0nce-over with touch up paint (cover all those screw heads!), and the bookcase door was DONE.

unnamed (7)
Ta Da!

For the left-side door, which would slide behind the bookcase, I created a graphic text art piece in Word.  Now I’m no graphic designer, so Word does me just fine.  I’m sure there are some fantastic programs for creating word art out there, but this works for little ‘ol me.  The verse I chose was Proverbs 17:17 – A friend loves at all times, and a brother is born for adversity.  I mish-mashed a couple versions to get the wording I liked best, and that would make the most sense to my little boys.  After measuring the area  I wanted for the text (factoring in the pull-cup handle that would remain on this door), I did a little dividing to get the measurements into inches on a standard page.  Then I created a rectangular outline of those dimensions and pieced together my verse with a couple different fonts and effects.  Here is how it came out on paper (well, on an ink-jet compatible transparency sheet that is!):

unnamed (5)

Then, I propped up the door, set up the projector, and taped down my transparency.  I used pencil to trace it out on the door, and then laid it out on the floor again to paint.  Since the door is a good 36″ wide, I tried to always start my words from the middle and work my way out, to avoid smudging or smearing.  At one point I had to laugh because the door said this:

unnamed (8)
Almost there!

unnamed (9)
That’s more like it.

The first coat didn’t come out quite perfect so I did go over it one more time.  Then it was *finally* time to hang these doors!  After removing the bi-fold doors and hardware, I installed the sliding door tracking.  That was simple enough.  Getting the doors to slide on their tracks was trickier.  First, the bookcase door was FAR heavier than before.  I was sweating, panting, and fighting it all the way.  Then, to my dismay, once the doors were up I could not budge them at all!  As it turns out, they were a quarter inch too long for the opening.  BUMMER.  Enter our terrific neighbor, Dave, with his circular saw to make all things right with the closet-door world!  After Dave trimmed the doors down, they went up without too much fuss and slid nicely.  Phew!

unnamed (15)
I don’t have a picture of Dave rescuing me from closet door doom, but I have to give him a shout-out.  This was taken last Christmas – our annual tradition of begging Dave to help haul the ginormous 14-foot live tree into the entryway.  We owe him.   A lot.

All right, back to the project.  One little thing I learned when installing new sliding door hardware is to pay really close attention to the wheel brackets which go on the top of the doors.  I didn’t realize when fastening these on that two of them have a deeper inset, allowing for the front door to slide with just the right distance from the back door.  I thought I was going crazy when the doors didn’t budge after I thought I’d gotten everything up just-so.  The instruction booklet was not my friend, to say the least.  I was so relieved when I finally figured it out!

41oTP945eCL._SY300_
Look closely at the depth of this part when you’re installing the hardware!

For those of you patient souls who actually made it to the end of this way-too-long tutorial – here is the finished product!  I have a few little finishing touches to complete, now that they’re up and I can see them in action: add trim to the headrail so the tracking is concealed, and add a little lip to the bottom of each shelf so skinny books can’t slide out.  But overall I am thrilled with the end result!  The boys are loving them too.  My soon-to-be-first grader can read the whole verse out loud, which just makes this mama’s heart burst with joy.  And, as a bonus, the boys are building massive muscles every time they slide the bookcase door.  It’s a beast!  But even the 3-year-old can do it, the little hulk.

unnamed (12)

unnamed (11) unnamed (13)

So, what do you think?  Does this inspire you to find creative ways to maximize the form and function of your space?
My neighbor’s daughter has already requested a set of these doors for her room.  I hope she gets ’em!

In His image,
Monique